Electric Low Capacity

Light Duty Commercial

Electric cement lined water heater Model E
  • Light Duty
  • 6 - 120 Gallon Capacity
  • Up to 12KW - 1 Phase or 3 Phase

Ceiling Hung Horizontal

Electric horizontal ceiling hung water heater Model HE/HSE
  • Horizontal, Ceiling Hung
  • 20 or 30 Gallon Capacity
  • Up to 20 KW - 1 or 3 Phase

Heat Pump
Hybrid

Hybrid electric heat pump water heater Model PBX
  • Heat Pump Water Heater
  • 40 - 120 Gallon Capacity
  • 1 or 3 Phase

Point-Of-Use Storage

Point-of-use electric water heater Model CE110
  • Point-of-Use
  • 1 Gallon Capacity
  • 1000 or 450 Watts - 1 Phase

Point-Of-Use Tankless

Electric tankless point-of-use water heater Model R
  • Whole House / Point-of-Use
  • Availabe 3 thru 27 KW - 1 Phase

Electric
Booster

Electric booster water heater Model J
  • Booster Heater
  • Provides 180°F water
  • Up to 88 KW - 1 or 3 Phase

Tankless Electric Booster

Electric tankless booster heater Model JTX
  • Tankless Booster Heater
  • Provides 180°F water
  • 11 to 54 KW - 1 or 3 Phase

Heavy Duty Commercial

Commercial heavy duty electric storage water heater Model SE
  • Heavy Duty
  • 6-120 Gallon Capacity
  • Up to 58 KW - 3 Phase

Tankless Commercial

Electric tankless water heater Model TX
  • Tankless Commercial
  • Highly efficient tankless
  • Up to 54 KW - 1 or 3 Phase

Large ASME
Heater

Large capacity electric storage tank water heater Model SH
  • Large Capacity
  • 80-5000 Gallon Capacity
  • All KW ratings - 1 or 3 Phase
     

Commercial Gas Tankless

Gas tankless water heater Model GX
  • High Efficiency Condensing Burner
  • Integrated Pump
  • 200,000 and 250,000 BTUs

Integrated Tank with Tankless

Condensing gas storage tank water heater Model GXT
  • High Efficiency Condensing Burner
  • Hydrastone Cement
  • 200,000 to 250,000 BTUs

DI / RO Gas
Tankless

DI/RO gas fired tankless water heater Model DGX
  • DI/RO Water Heater
  • High Efficiency Condensing Burner
  • 199,950 and 250,000 BTU

Gas Tankless Booster

Condensing gas tankless booster water heater Model JBX
  • Gas Tankless Booster
  • For Commercial Kitchens
  • 250,000 BTU

Gas Storage
Heater

Condensing gas storage tank water heater Model GXT
  • Non Condensing Burner
  • Hydrastone Cement
  • 200,000 to 250,000 BTUs
   

Large ASME
Steam Heater

Steam fired water heater large capacity Model ST
  • Storage Type
  • 80-5000 Gallon Capacity
  • ASME Stamped

Packaged Semi-Instantaneous

Semi-Instantaneous Steam Fired Water Heater Model STX
  • Semi-Instantaneous
  • Space saving design
  • Provides 10,500 GPH

Point-Of-Use
Steam

Storage tank steam fired water heater Model PS
  • Light Duty
  • 80-120 Gallon Capacity
  • For low demand/recovery

High Capacity Instantaneous

Instantaneous steam fired water heater Model F
  • Instantaneous
  • 7 Sq. Ft. of floorspace
  • Up to 120 GPM
     

Semi-Instantaneous Indirect

Indirect fired semi-instantaneous water heater Hubbell Model BWX
  • Semi-Instantaneous
  • Vertical or Horizontal
  • ASME Stamped

Large ASME
Indirect

Indirect fired storage tank water heater Hubbell Model BW
  • Storage Type
  • Vertical or Horizontal
  • 80-5000 Gallon Capacity

Small Capacity Indirect

Indirect fired storage tank water heater model T Transflow
  • Indirect Fired
  • 30-120 Gallon Capacity
  • Utilizes boiler water

Solar

Solar water heater Model SLN
  • Solar Heater
  • Vertical Storage Type
  • 30-120 Gallon Capacity
       

Storage
Tanks

ASME and None ASME storage vessels Hubbell Model StorageTank
  • ASME & Non ASME designs
  • Hydrastone Cement
  • Vertical or Horizontal

Buffer
Tanks

ASME and None ASME storage vessels Hubbell Model BufferTank
  • Carbon Steel Construction
  • Long Warranty
  • ASME Section VIII, Division 1
   
       

Circulation (Instantaneous)

Electric circulation heater Hubbell Model CR
  • Circulation (Instantaneous)
  • Heavy Duty Construction
  • 25-1600 KW - 1 or 3 Phase

Explosion
Resistant

Electric hazardous location water heater Model ER
  • Hazardous Location
  • 10-120 Gallon Capacity
  • Up to 58 KW - 1 or 3 Phase

Industrial Process Heater

Electric process industrial water heater Model V
  • Process Systems & Industrial
  • ASME Stamped
  • Up to 88 KW - 1 or 3 Phase

Emergency Shower Tankless

Electric tankless safety shower water heater Model ETX
  • Tankless Emergency Tepid Water
  • NEMA 4 Standard
  • Up to 88 KW - 1 or 3 Phase

RO / DI Heater Compact

DI/RO electric hot water heater Model HD
  • RO/DI Water Heater
  • Point-of-Use Heater
  • Up to 88 KW - 1 or 3 Phase

RO / DI Heater Storage

DI/RO electric hot water heater Model D
  • RO/DI Water Heater
  • 1-120 Gallon Capacity
  • Up to 88 KW - 1 or 3 Phase

Tepid Water for Emergency Fixtures

Electric safety shower water heater Model EMV
  • Emergency Tepid Water
  • Fully packaged system
  • Integrated mixing valve

Fully Integrated Package

Model Packaged Skid
  • Customized to your specifications
  • Full featured system ready for your application

Light Duty
Electric

Electric water heater for shipboard marine use single phase power Model ME
  • Light Duty
  • 6-120 Gallon Capacity
  • Up to 6 KW - 1 Phase

Large ASME
Electric

Electric water heater for shipboard marine use large capacity Model MSH
  • Large Capacity
  • 80-5000 Gallon Capacity
  • All KW ratings - 1 or 3 Phase

Heavy Duty
Electric

Electric water heater for shipboard marine use three phase power Model MSE
  • Vertical
  • 6-120 Gallon Capacity
  • 1 or 3 Phase - Up to 58 KW

Tankless
Electric

Electric tankless water heater for shipboard marine use model MTX
  • Tankless Marine Heater
  • Provides 180°F water
  • 11 to 54 KW - 1 or 3 Phase

Naval

Naval shipboard marine electric water heater Hubbell Model 177
  • MIL Spec Navy Heaters
  • Comforms to MIL-H-965
  • Shock and EMI protection

Fully Integrated Package

Turn-key hot water system
  • Customized to your specifications
  • Full featured system ready for your application
   

Immersion Heating
Elements

Electric immersion tubular style heaters
  • Immersion Electric Heaters
  • Flanged or Screw Plugs Types
  • All KW ratings - 1 or 3 Phase

Heat Transfer
Coils

Heat exchanger and heating coil water heaters
  • Immersion Heat Transfer Coils
  • U tube type
  • Range of Materials
   
       
Electric High Capacity
Gas Fired
Steam Fired
Indirect
Storage
Special Purpose
Marine
Elements & Exchangers
Resource Center
Electric water heater for shipboard marine use three phase power Model MSE
Still have questions? Complete this form
*Name:
*Email:
*State /
Province:
*Comment:

Model MSE

Shipboard Electric Water Heater

6-120 Gallon Capacity, up to 58 KW, Single or Three Phase

The Hubbell Model MSE water heater is specifically designed for marine use and is in conformance with USCG and is ABS Type Approved. By utilizing deck and bulkhead mounting supports, the water heater is securely fastened to the ship structure, thus providing a secure and reliable water heater installation. To ensure tank longevity, the high quality tank is constructed of steel and internally lined with specially formulated hydrastone cement. The Hydrastone Cement lining, along with solid copper-silicon threaded tank openings and a built-in heat trap device, all ensure a longer lasting, nergy efficient water heater that is resistant to the highly corrosive effects of hot water.

When you specify and install a Hubbell model MSE, knowing that it is in conformance with USCG regulations and ABS Type Approved, you will have confidence that the ship owner will be provided with a long lasting, trouble-free source for hot water.

Learn More About Hydrastone Cement Lining

ABS Type Approved Product cULUS Listed
  • Heavy Duty Construction

    • Hydrastone cement lining provides longer tank life
    • Copper-silicon alloy tappings cannot rust or corrode
    • High impact composite jacket cannot rust or corrode and eliminates damage during installation and transit
  • Marine Approvals

    • United States Coast Guard (USCG) conformance and American Bureau of Shipping (ABS) Type Approved
    • USCG conformance and ABS Type Approval eliminates costly delays and uncertainties during ship inspection
  • Wide Selection

    • Built to meet your exact needs
    • Numerous options available for specialized applications
  • Mounting Systems

    • Heavy duty legs secure the tank to deck
    • Side-Sway bulkhead attachment points provide added mounting integrity
    • The entire mounting system is integrally welded to tank for maximum stability and safety
  • High Efficiency

    • 2" thick polyurethane foam insulation reduces heat loss
    • Built-in heat trap lowers operating costs
  • Reliable

    • Full five (5) year Non Pro-rated tank warranty is standard
    • Full ten (10) year Non Pro-rated tank warranty can be specified for extended protection

Model MSE Water Heater Specifications

Capacities: 6 thru 120 Gallons
Orientation: Vertical
Voltages: 120 thru 600 Volt
Phase: 1 or 3 φ
Inlet Size:
Below 45 KW: 3/4" Female NPT
45 KW and over: 1 1/2" Male NPT
Outlet Size:
Below 45 KW: 3/4" Male NPT
45 KW and over: 1 1/2" Male NPT
Drain Size: 3/4" GHT Hose Connection
Relief Valve Size: 3/4" Female NPT
Relief Valve Type: T&P, 210°F, 100 psi
Hi-Limit: 190°F
Thermostat Range:
Surface: 110-170°F
Immersion: 100-190°F
Design WP: 100 psi
Design TP: 300 psi
Elements: Incoloy Sheathed
Insulation: 2" Polyurethane Foam
Tank Warranty:
Standard: 5 Year Non Pro-Rated
Optional: 10 Year Non Pro-Rated
Electrical Warranty: 1 Year
Jacket: High Impact Colorized Composite
Finish: White with Black
Marine Classifications: ABS Type Approved

General Specifications

  • 1/2" thick Hydrastone cement lining
  • Integrally welded bulkhead attachment points
  • Heavy-duty integrally welded leg supports for deck mounting
  • Non-ferrous solid copper-silicon threaded openings for maximum corrosion resistance
  • Magnetic contactor(s) are heavy duty resistive load type rated for 200,000 cycles
  • Low voltage control circuit (fused) transformer (units over 240 volt)
  • Power circuit fuse protection (units over 48 amp)
  • Incoloy sheathed immersion heating elements
  • Built-in heat trap to improve operating efficiency (3/4" only)
  • Surface thermostat 110-170°F range
  • Immersion thermostat (100-190°F) furnished as standard when required due to high recovery versus storage ratio.
    On 6-30 gallon heaters over 5 KW
    On 40 and 50 gallon heaters over 8 KW
    On 65 gallon heaters over 12 KW
    On 80-120 gallon heaters over 15 KW
  • Surface safety hi-limit cut out with manual reset button (190°F)
  • Immersion safety hi-limit cut out with manual reset button (Standard on heaters 45 KW and above)
  • ASME rated temperature and pressure relief valve set at 100 psi, 210°F
  • 2" thick polyurethane foam insulation
  • High impact non-corroding colorized composite protective jacket
  • Cold water inlet diffuser with drain valve

Outline Dimensions

Outline Dimensions

Model MSE Dimensional Data

Storage Capacity (Gallons) Base Model Number Maximum KW Input Dimensions (Inches) Shipping Weight (lbs.)
Overall Diameter Overall Height Deck to Inlet "A" Deck to T&P "B" Bulkhead Mounting Dimension "C" Bolt Circle "D"
6 MSE06 3 15 17.5 5 12.5 None None 120
10 MSE10 10 20 27 13 21 None 13 155
20 MSE20 10 20 39 13 33 None 13 195
30 MSE30 15 20 47.5 13 40 12 13 225
40 MSE40 15 20 64.75 13 57 12 13 315
50 MSE50 58 22.75 57 13 49 12 15 330
65 MSE65 58 26 54 14 46 12 18 395
80 MSE80 58 26 64 14 57 12 18 430
100 MSE100 58 26 75.5 14 68 12 18 460
120 MSE120 58 28 75.25 14 68 12 20 510
40 MSEU40 58 26 39 13 30 None 18 320

Formulas To Solve For:

Recovery

GPH x _____________ °F ΔT x 0.00244 = KW
KW x 410 ÷ GPH = ____________ °F ΔT
KW x 410 ÷ __________ °F ΔT = GPH
Note: 1 KW will heat 4.1 GPH at a 100°F ΔT

Electrical

((KW x 1000) ÷ Volts) ÷ 1.73 = Amps 3 Φ
(KW x 1000) ÷ Volts = Amps 1 Φ

KW BTU/HR Gallons Per Hour Heated At
Various Temperature Rises
Amperage Ratings At Various Voltages
Single Phase Three Phase
60 °F Δ 80 °F Δ 100 °F Δ 208V 240V 480V 208V 240V 380V 415V 440V 480V
3 10,236 21 15 12 14 13 6 8 7 5 4 4 4
4 13,648 27 21 16 19 17 8 11 10 6 6 5 5
6 20,472 41 31 25 29 25 13 17 15 9 8 8 7
8 27,296 55 41 33 39 33 17 22 19 12 11 11 10
10 34,120 68 51 41 48 42 21 28 24 15 14 13 12
12 40,944 82 62 49 58 50 25 33 29 18 17 16 15
15 51,180 103 77 62 72 63 31 42 36 23 21 20 18
18 61,416 123 92 74 87 75 38 50 43 27 25 24 22
20 68,240 137 103 82 96 83 42 56 48 30 28 26 24
24 81,888 164 123 98 115 100 50 67 58 37 33 32 29
30 102,360 205 154 123 144 125 63 83 72 46 42 39 36
36 122,832 246 185 148 173 150 75 100 87 55 50 47 43
40 136,480 273 205 164 192 167 83 111 96 61 56 53 48
45 153,540 308 231 185 216 188 94 125 108 69 63 59 54
50 170,600 342 256 205 240 208 104 139 120 76 70 66 60
54 184,248 369 277 221 260 225 113 150 130 82 75 71 65
58 197,896 396 297 238 279 242 121 161 140 88 81 76 70
Notes:
1. The KW selections above are shown for convenience. A full selection of KW ratings from 1 to 58 KW is available
by simply entering the desired KW into the model number.
2. Units 45 KW and over are supplied with 1 1/2" Male NPT inlet/outlet connections and immersion hi-limit.
3. Alternate voltages including 220, 230, 460, 575 and 600 volt are available. Please contact us directly.

Optional Equipment

  • Full 10 Year Non Pro-Rated tank warranty
  • Control circuit (fused) transformer. (Standard on units over 240V)
  • Electronic low water cut off
  • Power circuit fuse protection
  • Immersion thermostat (specify 100-190°F or 30-110°F Range)
  • Immersion adjustable (100-240°F) safety hi-limit cut out with manual reset
  • Solid Type 304 or 316L stainless steel tank, 90/10 copper nickel alloy tank
  • 1 1/2" Male NPT brass inlet and outlet water connections (heat trap not available)
  • 2" Male NPT brass inlet and outlet water connections (heat trap not available)
  • Special connection size/type
  • Combination temperature and pressure gauge: 2 1/2" dial, 30-240°F, 0-200 psi - factory installed in tank
  • Built-in circuit breaker, specify with or without shunt trip protection
  • Built-in non-fused On/Off disconnect switch
  • Electro-mechanical 7-day time clock wtih battery back-up
  • Horizontal construction
  • NEMA 4 weather resistant construction for installation in outdoor/wet areas
  • Explosion resistant enclosures for hazardous locations
  • Secondary heating capability provided by a tank inserted heat exchanger constructed from single wall (Optional: double wall) copper fin tube
  • Additional ground connections
  • Alternate working pressure available

Model Number Designation MSE



Step 1
Model:
MSE
Step 2
Storage Capacity:
6-120 U.S. Gallons
-
Step 3
Upper KW:
Element bank
0 - 58 KW
(typically 0) Not
available in 6,
10, 20 Gallon
capacity heaters
-
Step 3
Lower KW:
Element bank
1 - 58 KW

Step 4
Tank:
SL = Hydrastone Cement
lined tank
SS = Solid stainless
steel tank
CN = Solid 90/10
copper-nickel tank

Step 5
Voltage/Phase/Hz:
RS = 208-1-60
R = 208-3-60
S = 240-1-60
T = 240-3-60
W = 277-1-60
T3 = 380-3-50/60
T7 = 415-3-50/60
T5 = 440-3-60
T4 = 480-3-60
T4S = 480-1-60
T6 = 600-3-60

Example:

MSE120 - 0 - 45SLT4

Hubbell model MSE marine water heater with a storage capacity of 120 Gallons with 45 KW in the lower element bank. Storage tank is lined with Hydrastone cement and the electrical controls operate at 480 V, 3 phase, 60 Hz power.


Model MSE Spec
        Printable Version

Model MSE Specific Questions

Is a glass lined tank recommended for marine use?

Not in a commercial marine environment. The real cost of a water heater in a marine environment, especially commercial marine, is the cost of replacement. Therefore, it makes economic sense to install a water heater with a long life expectancy. Hence, glass lined water heaters are not the best choice in a marine environment when a cement lined water heater can typically provide 3 times longer life in comparison.

Which is better for me, a tankless or storage type water heater?

It depends. A tankless water heater is sometimes referred to as a Point-of-Use (POU) or instantaneous water heater. Due to the relative small physical size of a tankless water heater compared to a storage tank water heater, a tankless option can be advantageous from a space saving perspective and can sometimes be installed closer to where you want hot water (hence the term POU). However, tankless heaters are not suited for many applications, so it is critical that before choosing to go tankless you have carefully considered all of the factors that sometimes make the tankless option more complicated and risky compared to a storage type water heater. In particular, you should understand the operational characteristics, maintenance requirements, reparability, and sometimes significant installation requirements of a tankless water heater before making a decision. Tankless units do not store heated water like a storage type water heater; they only heat water as there is demand and therefore must be sized to meet the maximum flow for the application. In some cases a tankless water heater may improve operating efficiency, but possibly at the expense of user comfort. Hubbell tankless water heaters are available in Electric Tankless or Gas Tankless

Why is Hydrastone Cement a better choice over glass lining?

Cement lining provides guaranteed 100% coverage with a minimum thickness of 0.5” over all internal tank surfaces. In comparison, glass lining is approximately 0.005” thick and includes imperfections, pinholes and variation in coverage thickness resulting in portions of unprotected steel tank exposed to corrosion. In an attempt to compensate, glass lined tanks include a sacrificial anode in an effort to slow down the corrosion of the tank. Cement lined tanks on the other hand do not require an anode due to the integrity of the lining. As such, a cement lined tank will far outlast a glass lined tank. For a more complete explanation of the benefits of the Hubbell cement lining please click on the following link Cement Lining

Is American Bureau of Shipping (ABS) approval needed?

Equipment and specifically water heaters for use in commercial marine applications require special construction features to ensure longevity and proper operation in a marine environment. In addition, the water heater must be constructed in conformance to the Code of Federal Regulations USCG 46 CFR Part 53.01 and the pressure vessel must be designed and constructed to the proper ASME code and stamped. A Hubbell marine water heater is manufactured under a Certificate of Manufacturing Assessment as issued by American Bureau of Shipping (ABS) Here

What is a sacrificial anode and does a cement lined tank need one?

All water heaters constructed using a steel tank requires a lining to protect the internal steel surfaces from corrosion. Certain linings (i.e. glass and epoxy), due to their nature, have unavoidable holes and imperfections resulting in exposure of the steel tank. As a result of this deficiency, the manufacturer will install an anode rod(s) in an attempt to delay corrosion of the steel tank. An anode rod is typically made of aluminum, magnesium or zinc, is a maintenance item that requires periodic inspection and replacement, and is often times the cause of a “rotten egg” odor to your hot water. Often referred to as a sacrificial anode rod because, over time, it slowly dissolves, sacrificing itself as it is attacked by aggressive substances in the water which would otherwise attack the steel tank through the pinholes and imperfections of the glass or epoxy lining. A cement lined steel tank on the other hand does not require an anode because of the thickness and guaranteed 100% coverage of the cement lining over all internal surfaces of the steel tank. This eliminates the need for an anode rod in a cement lined water heater, resulting in a significantly longer life compared to a glass or epoxy lined water heater. For a further discussion please click on the following link Cement Lining

General Questions

Where can I purchase a Hubbell water heater?

There are numerous ways to purchase a Hubbell water heater depending upon the model you desire and your geographic location. The easiest way is to contact Hubbell directly at 800-647-3165 and ask for the sales department where you will be directed to either our local representative or our order entry department for quick and easy ordering.

Where can I purchase replacement parts?

Parts are available for your Hubbell water heater direct from the factory. Please call 800-647-3165 and ask for our parts department. Please have your model and serial number handy.

I don't see the size or feature I need, what do I do?

Hubbell has more than 35 product families available in over 4,000,000 configurations. There are numerous features, configurations and ratings we provide but for practical reasons are are not listed in the sales brochure. If you have a specific requirement and you do not see it in the brochure, please contact a Hubbell Sales Engineer...chances are we have what you need.

What should I know about Legionella disease?

Legionella is the bacteria responsible for Legionnaire’s Disease, an acute bacterial infection of the lower respiratory tract. This bacterium was first identified in 1977 by the Centers for Disease Control as the cause of an outbreak of pneumonia that caused 34 deaths at a 1976 American Legion Convention in Philadelphia. Pontiac Fever is a less severe, non-pneumonia, flu-like disease that is associated with and likely caused by Legionella bacteria. Legionella is a fairly common water bacterium and has been found to exist widely in many surface water sources including lakes, rivers, streams and ponds. It can also be found in ground water sources and some soils. At the levels found in these naturally occurring sources it typically does not pose a threat to public health. When the bacterium enters a domestic water system it can find an ideal host environment of warm water temperatures (105-115°F), stagnant water areas (isolated storage tanks and dead-end piping legs) and ample food sources (sediment, scale, deposits and biofilm). Under these conditions Legionella can rapidly colonize, forming higher concentrations that can pose the public health threat of Legionnaire’s Disease. There are many methods of controlling colonization of Legionella bacteria. However, a widely accepted and preferred method is to maintain the hot water system storage temperature continually at or above 140°F. Unfortunately, the elevated temperature necessary to minimize the growth of and kill Legionella bacteria has the potential to cause serious thermal shock and scalding injuries. As such, many plumbing engineers will specify that the water heater be set to maintain water temperatures at 140°F or higher to reduce the risk of Legionella, but then specify the appropriate mixing valve to ensure safe delivery of hot water to the fixtures. For a more thorough discussion of Legionella please go to here and the following link to the US Department of Labor OSHA information regarding Legionnaires’ Disease OSHA here

My question is not found in these FAQ’s, where do I look next?

Check out the Hubbell Product Center at Here for a complete listing of all technical documentation available by model. Get easy access to Installation, Operation & Maintenance manuals, Sales Brochures, Service Bulletins, Wiring Schematics, Parts Breakdowns and various other technical documents related to the full line of Hubbell water heaters. Or, if you prefer, please call us at 800-647-3165 and ask to speak to a Sales Engineer.

Downloads

Many of our products literature is available online for download. To open these files, a PDF viewer is required. If you do not have one, Adobe provides Acrobat Reader free of charge for viewing only. Use this link to download Acrobat Reader. You may also choose to download the file to your PC for future reference or printing. On most operating systems, simply right-click on the links below, choose "Save target as..." or "Save link as...", choose a location and it will save the document to your computer for future reference.

Model MSE Specific Questions

My question is not found in these FAQ’s, where do I look next?

Check out the Hubbell Product Center at Here for a complete listing of all technical documentation available by model. Get easy access to Installation, Operation & Maintenance manuals, Sales Brochures, Service Bulletins, Wiring Schematics, Parts Breakdowns and various other technical documents related to the full line of Hubbell water heaters. Or, if you prefer, please call us at 800-647-3165 and ask to speak to a Sales Engineer.

Where can I purchase replacement parts?

Parts are available for your Hubbell water heater direct from the factory. Please call 800-647-3165 and ask for our parts department. Please have your model and serial number handy.


For Further Assistance Please Contact a Hubbell Tech Support Rep.

Sam Wellington
samw@hubbellheaters.com
203-378-2659 x136
D.J. Dineson
djdineson@hubbellheaters.com
203-378-2659 x125
Hubbell Heaters
45 Seymour Street
P.O. Box 288
Stratford, CT 06615-0288
Tel: 203-378-2659
Fax: 203-378-3593
Product Center
Hubbell Binder

View our current digital materials available in our resource center.

To Product Center  Bullet Point